You Are Cute Builder Gel №58, 15ml

You Are Cute Builder Gel is a light-curing polymer material that, thanks to its strength, allows for significant nail plate extension. It contains photoinitiators that initiate the polymerization process when the material is exposed to ultraviolet light of a specific wavelength.

Features:

- Acid-free.
- Medium consistency, more like a liquid.
- Light caramel pigmentation with a translucent effect.
- Suitable for the no-file technique.
- Suitable for "top-up" extensions.
- Does not cause burning in the lamp.
- Thickens in cold temperatures and thins out in warm temperatures.
- Thixotropic – thins out if you move the brush while working.
- It can be additionally heated to thin out the gel.
- Hard at 1 mm. If the thickness is less than 1 mm, it may flex slightly, but this does not affect wear. - Does not shrink and holds the arch well.
- Requires a Rubber Base base.
- Curing wavelength: 365-405 nm.
- UV/LED lamp power: 36-48W.
- Acceptable coating thickness: 0.5 mm at the tip/1 mm at the apex.
- Full cure time: 120 seconds.

Application Method:

STRENGTHENING:

1. Removal.
2. Do not file the nail shape or leave a 2 mm length, which will be removed after smoothing.
3. Use a 220 grit file to dust the nail from above, lifting the scales of the nail plate, or use a 100 grit buff.
4. Perform a manicure.
5. If working with removers, wash your hands with soap after use. 6. Degrease the nail with Nail Prep. Do this in two stages. Use 4 wipes (1 wipe per 5 fingers). First stage: wipe the surface of the nail. Second stage: take an orange stick, place the wipe on it, and wipe the entire cuticle area and crevices.
7. Use a primer if desired, but if the base coat is sufficiently acidic, it is not necessary.
8. It is best to apply the Rubber Base liner with a flat gel brush. Apply the base coat in an even layer. Fill all the crevices of the nail and cure in the lamp for 60 seconds.
We recommend leaving the tacky layer on the base coat, as it helps chemically bond with the subsequent layers of the coating (gel, color, base coat). Removing the tacky layer weakens the chemical adhesion and reduces the risk of peeling.
9. Smooth out. If using gel, leave a 0.5-1 mm gap from the cuticle. Cure in a lamp for 60 seconds.
10. File the shape after smoothing. This is necessary to create a thickness at the edge of the nail that will support the free edge.
11. If the nail was thin, it may curl, so be sure to file 1 mm of the natural nail from the inside. This will prevent the material from peeling off. If the material is hard and the nail is very soft, the nail itself will begin to separate from the hard material at the free edge.
12. After dusting, wipe off the tackiness and apply gel polish.
13. Apply top coat. Cure for 120 seconds. After drying, do not wipe with anything, as this may cause the shine to fade.

CLASSIC NAIL EXTENSIONS

1. Removal
2. Shorten the nail to 1 mm and shape it into a round shape. 3. Using a 220-grit file, gently dust the nail from above, lifting the scales of the nail plate, or use a 100-grit buff.
4. Perform a manicure.
5. If using removers, wash your hands with soap afterward.
6. Degrease the nail with Nail Prep. Do two passes. Use four wipes (one wipe for every five fingers). First pass: wipe the surface of the nail. Second pass: take an orange stick, place the wipe on it, and wipe the entire cuticle area and crevices.
7. Apply primer.
8. It's best to apply the Rubber Base liner with a flat gel brush. Apply the base in an even layer. Fill all crevices of the nail and cure in the lamp for 60 seconds.
9. We recommend leaving the tacky base coat on, as it helps chemically bond with subsequent layers of polish (gel, color, base coat). Removing the tacky layer weakens the chemical adhesion and increases the risk of peeling.
10. Apply the form to extend the free edge of the nail.
11. Apply gel to the artificial nail form. Cure for 30 seconds.
12. File the free edge and shape the nail.
13. Wipe off any tackiness and excess dust.
14. Apply Rubber Base again to the areas where the file was used. Cure for 30 seconds.
15. Smooth the gel over the nail, place it in the lamp, and clamp it for 10-15 seconds. If the gel is very tacky, clamp it for 20 seconds.
16. Cure in the lamp for 120 seconds.
17. Wipe off any stickiness before applying gel polish.
18. Apply top coat. Cure for 120 seconds. After drying, do not wipe with anything, as this may cause the shine to fade.

Ingredients: Acrylates Copolymer, Hema, Silica Dimethyl Silylate, Dimethicone, Ethyl Trimethylbenzoyl Phenylphosphinate
May contain: CI 77891, CI 18965, CI 15510, CI 73360, CI 738 74260, CI 77266

TPO FREE
(Product photos on the website may differ from the actual product)